Back to Home
 

Picture Tour

Click here to begin a sequential tour through the photos listed below.

There are currently 47 photos in this section

50 hp HSI 051-07 with 38" cartridge pulse jet
8 operators x 1.5" ID hose
700 ft long pipe runs

Surge control visible beside light
tank on blower closest to motor is the safety inline filter

Close shot of the filter and panel
high level probe shown

Close-up of the inline filter a differential pressure gauge and shut down pressure switch (broken bag detector) is shown

100 Hp HSI 081-05 shown c/w starter panel, surge meter, and disconnect three (3) x 3" hoses for fiberglass conveyed 250 ft and discharged into the charge chamber of a compactor

View of the 60" separator outside

Close up of separator showing 24" x 24" rotary air lock inlet wearstrip is also visible under blue duct

Two 60" diameter pulse jets being loaded for the jobsite

Fifty (50) simultaneous operators.
Two 66" cartridge pulse jets, three exhausters staged.

Operates at 168A but stages down to just 17A!

Turnkey design, union installation of electrical and mechanical.

Three exhausters stage up and down according to demand.

Cartridge filters easily assessable from custom designed support frame.

Fifty (50) simultaneous operators with 1.5" x 50ft long hoses. Two 66" cartridge pulse jets with walk in design. Diaphragm valves brought low for one level service access.

325 Hp total, 5000 cfm @ 10.5" Hg. Stages down to just 40A minimum!

Starter panel with A-B SmartTouch Controller

Starter panel with single A-B soft start controller and three separate starters to stage load up and down with demand.

38" diameter pulse jet with explosion vent
and custom support frame.

25 Hp centrifugal with inline HEPA filter.
Supports five operators with 1.5" x 30ft hose.

1.5" inlet valves on every column.

Typical 25 hp starter and control panel.

High vacuum liquid only central vacuum.
10 gallons in 2.5 seconds.
NOT MUCH ROOM!

Automatic PLC controlled discharge and wash down
sequence with LED indicators

4" hose and lightweight ergonomically designed tool
picking up wood dust at a belt transfer point

4" hose and tool at transfer point

Vacuum pump and 50 Hp motor
850 cfm @16" Hg with sound enclosure

Sound enclosure, control panel, and inline filter.
Note the check valve on intake of the inline.

Close up of 50 Hp vacuum package.
The screened intake provides bleed air when
all inlet valves are closed (reduced idle valve).

48" pulse jet filter with 50 cf of storage.
24" x 24" gate valve discharges to bulk bag.
Custom fabricated support frame with safe service access.

8000 cfm fan with 50 Hp diesel engine and
on board air compressor.

Explosion Proof 75 Hp Starter and Control Panel.

75 Hp vacuum skid with 304SS inline filter and
twin discharge silencers hung from frame.

Portable 50 Hp centrifugal vacuum skid and
soft start control panel.

15,000 cfm dust collector, turnkey supply and install.

1050 cfm @ 10" Hg. portable with 31 Hp B&S engine.

650 cfm @ 16" Hg 30 hp portable with 40 cf storage.
Model PL30 with 4" cam inlet

650 cfm @ 16" Hg portable with 30 Hp TEFC motor and 40 cf storage.

40 cf roll forward hopper from PowerLift

The PowerLift inlet packs abrasive material so that it wears on itself.  Note that after two loads of concrete dust the filters (in background) still look like new.  Exclusive design lowers abrasive wear and reduces filter loading to ultra low levels.

The PowerLift PL50 850 cfm @ 17" Hg continuous with 2.50 cubic yards (68 cf) material storage
and reverse jet cleaning.

Vacuum skid 2300 cfm @ 18" Hg. (peak) and
150 Hp TEFC motor with temperature switch.

12" Plattco double dump discharge valve
with pneumatic actuators.

66" diameter pulse jet with 823 sf high efficiency filter and 8" Plattco double dump discharge valve.

66" diameter pulse jet (left) with 10 cubic yard storage cyclone (right) and custom structural frame.
Whole assembly needed to be brought up in "small" pieces for local assembly.

A load of custom bends fresh from painting.

Twenty five (25) simultaneous operators with 1.5" x 50ft long hoses.
Single 66" cartridge pulse jets with walk in design.
Diaphragm valves brought low for one level service access.

100 Hp total, 2500 cfm @ 8.0" Hg. stages down to
just 37A (see next page) and still conveys material!
 

140A installed stages down to just 37A to save energy when the system is being lightly used.

10,000 cfm system collects wet aluminum chips
from 400 ft away, shreds them, dries them, and
discharges them into an existing dry chip conveyor.

150 Hp direct driven positive displacement
vacuum producer in a custom sound enclosure.

30 Hp custom designed enclosure.  Skid mounted & compact, required to run under 80 dba for both discharge and radiated noise.